manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 20

12

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

Installing Batteries

The 

PL4/PLS4 Control System

 

Wireless Controller is shipped with four AA-size alkaline batteries. Before using 

the unit install the batteries.
To install batteries:

1.  Place the PL4/PLS4 Control System

 

Wireless Controller

 face down on a flat clean surface. Remove the six 

screws securing the battery cover. Set the cover aside.

2.  Load the four batteries into the battery compartment. Orient the positive polarity end of each battery as shown 

below.

3.  Install the battery cover and secure with the six screws. Make sure that the battery cover is secure and that all 

the screws are hand tightened. CAUTION - DO NOT OVER TIGHTEN THE SCREWS. OVER TIGHTENING THE 
SCREWS CAN DAMAGE THE UNIT.  

4.  Power up the unit: To switch the unit on, press the Power On button located on the front of the unit. 
5.  Display messages after replacing batteries: After replacing depleted batteries a check battery message is 

displayed on the screen. Press the MENU button to continue.

6.  The screen will then display a second message to check the battery cover. After checking that the battery cover 

is secure and that all screws are tightened, press the MENU button. 

 

The battery icon should display the fully charged icon. The unit is ready for use.

S

crew (6x)

EasyTouch PL4/PSL4 Control System Wireless Controller (rear view)

Battery cover

+

+

+

+

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands