manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 74

66

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

Setting up the Wireless Controller for the first time

Setting up the EasyTouch

®

 PL4/PSL4 Control System Wireless Controller

In order for the EasyTouch PL4/PSL4 Control System Wireless Controller to communicate with the EasyTouch 
PL4/PSL4 Control System Outdoor Control Panel, the first time the wireless device is powered up it must first 
be assigned a unique communication address. For this process you need to access the menu for each control 
panel. For convenience it’s easier to setup the wireless device at the outdoor control panel.

From the EasyTouch PL4/PSL4 Control System Power Center outdoor control panel

1. 

Switch power on to the Power Center. 

2.  Press 

Menu 

button, and select 

Settings > Address

 and press the 

Right

 arrow button.

 

The outdoor control panel will display “Scanning...” for about five seconds while it searches for the 

Wireless Controller within range of the transceiver antenna. After the scanning process has finished, 
“Sending Address” is displayed. The system is now waiting to lock on to the Wireless Controller. 
Proceed to step 3.

From the Wireless Controller

3.  Press the 

Power On

 button located on the front of the Wireless Controller.

 

Note: 

After replacing depleted batteries a check battery message is displayed on the screen. Press 

the 

MENU

 button twice to continue.

4.  Press 

Menu

 button, and select 

Settings > Address

 and press the 

Right

 arrow button.

5.  Select “Address” and press the 

Right

 arrow button to lock on to the unique address that is being 

transmitted from the outdoor control panel. 

 

Note: If you choose “Abort,” the device can continue to operate using the factory default address. 

If the outdoor control panel has been previously addressed, the wireless may not operate the 
system. Each time the device is switched on the “NO ADDRESS” will be displayed. This mode is not 
recommended for permanent use.

6.  After selecting “Address” the wireless device unit will lock on to a unique address and display

 

“Found ADDRESSED.” Press the 

Menu

 button to save and exit this mode. The device is ready for 

operation.  

7. 

On the outdoor control panel:

 Press the outdoor control panel 

MENU

 button three times to exit 

the “Sending Address” mode and return to the main screen. The system will continue to transmit an 
address until the Menu is button is pressed to stop the process.

 

Note: To readdress the Wireless Controller, repeat steps 2 through 7 on the Wireless Controller to 

restart the address process.

Note: “Unit Mismatch” displays if the outdoor 
control panel has an existing system image. See 
page 12 for details. 

  Address Wireless                

 Sending Address.. 

 

       <MENU> 

 

  Address Wireless                

 Scanning ... 

 

 NO ADDRESS                

   

    Address 

    Abort 

 

 

 Address Lock                

  Found 

   ADDRESSED 

       <MENU> 

 Unit Mismatch                

  Download from

       Outdoor 

 

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands