manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 21

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

  13

 

EasyTouch

®

 PL4/PSL4 Control System Outdoor Control Panel Operating Modes

The EasyTouch PL4/PSL4 Control System can run in automatic mode or manual mode. Use the “Mode” button 
to switch the system from “Auto” mode (normal operating mode) to “Service” for manual operation and service 
purposes. Before operating the system, familiarize yourself with the LCD status messages and operating buttons.    

AUTO (Automatic): 

The system is in normal operating mode. 

Scheduled programs will run automatically.

 

HEATER:

  Displays the heat source (

Off, Heater, Solar Prf., Solar) 

as specified in the Heater menu settings (see page 30). When the 
Filter Pump (F) button is pressed in “Pool” or “Spa” mode, and heat 
source is enabled (Heater button LED on). 

POOL (SPA):

 Indicates that the Valves (V) button is in “Pool” or 

“Spa” mode and the Filter Pump (F) button has been pressed to 
switch on the filter pump. If this display line is  blank, it indicates no 
spa or pool function is active.  For a single body system, Hi-Temp 
(Spa) / Lo-Temp (Pool) sets the temperature settings (see page 44)

85° F / 100° F:

 Displays the actual spa or pool water temperature 

(85° F) and the set point temperature (100° F) as set in the “Heat” 
menu (see page 30).

AIR:

 Displays the actual outside air temperature (70° F) as read by 

the air sensor located near the Power Center.

Date  and Time:

 Displays the system day and time as specified in 

the “Clock” menu settings (see page 34).

Valves (V) button: 

When in normal 

operating mode, the system is in “Pool” 
mode so that only the pool water is 
circulated through the system.  Press the 
Valves button to enable “Spa” mode and to 
rotate valves and activate the Filter pump 
(Filter Pump LED on) automatically so that 
only the spa water is circulated through the 
system.  Note that the filter pump will switch 
off while the pool/spa valves are rotating 
into position.

 

“Fill/Spillway” and “Drain” 

modes are used only in “Service” mode. 

MENU / BACK button:  

Access the system menu. 
Also used to save and exit 
from a current menu or 
sub-menu settings. While 
in menu mode, all system 
control panel buttons are 
disabled. Press this button 
twice to refresh the display.

AUTO           HEATER
SPA       85°F / 100°F 
AIR          70°F
   MON  09:30 AM 

Filter Pump button:  

For spa operations, press the 

Valves (V)

 button to rotate 

valves into “Spa” mode, then 
press the 

Filter (F) 

button 

to activate the filter pump.  
Press the Valves button to 
toggle to “Pool” mode.  The 
Heater button LED will be on 
if a heat source is enabled in 
the Heat menu. 

Left and Right 
Button:  

Use these buttons to 
lower and raise the 
current set point water 
temperature level.

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands