manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 61

 

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

 

  53

 

EASYTOUCH PL4/PSL4 CONTROL SYSTEM WIRELESS CONTROLLER: 
Settings Menu: Backlight

Use the backlight  “On Time” option to set the duration that the backlight will stay on. The “Brightness” setting 
allows you to set the backlight brightness. These options can help to reduce power consumption and extend 
battery life. The Backlight options are:

• 

On Time:

 Backlight will stay on for 60 seconds, 30 seconds, five minutes, or “Backlight” feature is 

off. The default setting is 30 seconds. 

• 

Brightness:

 Backlight brightness can be set to low, medium or high. The default setting is medium. 

 

Backlight

To set the backlight duration and brightness: 

MENU

s

SETTING

s

BACKLIGHT

 

Up/Down buttons: 

Select 

5 S, 15 S, 30 S, 60 S, 5 M

 or 

OFF

 for the backlight to stay 

on.

 

Right button: 

Select 

LOW, MED or HI 

for the backlight brightness setting.

 

Press the Back button to save the settings and to return to the previous screen.

Settings Menu: Wireless Addr

Use this feature to assign the EasyTouch

®

 PL4/PSL4 Control System Wireless Controller a unique 

communication address to allow the wireless device to operate with the EasyTouch PL4/PSL4 Control 
System outdoor control panel (see page 64). 

Wireless Addr

To search and lock on to the EasyTouch PL4/PSL4 Control System wireless controller:

MENU

s

SETTING

s

WIRELESS ADDR

w

Press Right Arrow button

 

   

  Address Wireless                

 Sending Address.. 

 

       <MENU> 

 

  Address Wireless                

 Scanning ... 

 

BACKLIGHT OPTIONS

On Time: 30 S 

Brightness: MED

Right button: 

Press this button to automatically search and lock on to the  

Wireless Controller within range of the transceiver antenna.

 

For more information about the Wireless Controller, see page 70
Press the 

Menu

 button to save the settings and to return to the Settings 

menu selections.

Important Note:

1.   After you plug in a transceiver or power up the unit, wait at least 60 seconds before addressing the unit.
2.   If the wireless unit times out and power off before locking on the address, set the auto power off time to 

5 minutes then start the addressing. Remember to set it back to 1 minute after it is working or battery 
life is greatly decreased.

3.   If you are working with multiple sets of transceivers and handhelds make sure you keep them separated 

into sets.  

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands