manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 60

52

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

Settings Menu: Set Password

If required, the password feature allows you to password protect the EasyTouch PL4/PSL4 Control System 
control panel. To access a password protected control panel, you must enter the correct four digit password 
before access is granted.   

Password

To enable the password protect feature:

MENU

s

SETTING

s

SET PASSWORD

 

Up/Down button: 

Select the password 

first 

digit (0-9) of the four digit password. 

Right button: 

Select the next password digit. Repeat the previous step to enter each 

of the password digits. 

Right button: 

After you are finished entering the four password digits, press the 

Right button to enable the password feature. 

Up/Down button: 

Select 

Yes

 enable the password feature.

Press the 

Menu

 button three times to save the settings and to return to the main 

screen.

Note:

 If the password feature is enabled, the current four digit password can be 

viewed from the EasyTouch PL4/PSL4 outdoor control panel in the “Set Password” 
setting. 

 

Settings Menu: Erase EEPROM (Erase System Memory)

EasyTouch

®

 PL4/PSL4 Control System configuration data is stored and retained in “Flash” memory in an 

EEPROM located on the control panel main circuit board, and optional Indoor Control Panel. The EasyTouch 
PL4/PSL4 Control System user system configuration data can be erased to restore the factory defaults 
settings. System information automatically downloads from programmed components to non-programmed 
components in case of accidental memory loss and to ease board replacement. Any optional controllers (iS4 
and QuickTouch

®

 II QT4 Wireless Controller) that were configured need to be reconfigured. 

Erase EEPROM

The following procedure describes how to erase the system memory from either the main EasyTouch PL4/
PSL4 Control System control panel or the EasyTouch PL4/PSL4 Control System Indoor Control Panel. 

CAUTION: This procedure will erase all system settings. Any optional controllers will need to be reconfigured.  

MENU

s

SETTING

s

ERASE EEPROM

w

ERASE EEPROM

 

Up/Down button: 

Select 

Yes

.

 

 
 
Right button: 

The message 

“Erase EEPROM Are You Sure? No” 

is displayed. 

 

Up/Down button: 

Select 

Yes

.

 

 
 
Right button: 

Press this button to erase system data and restore the factory defaults. 

The display will go blank, then the main screen will be displayed.

Set Password 

 

PW      : [0000] 

Enable : No 

Erase EEPROM 

 

Erase ALL? No (Yes)

Erase EEPROM 

 

     Are You Sure? 

          No (Yes)

AUTO           HEATER

SPA       85°F / 100°F 

AIR        70°F

   MON  09:30 AM

 

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands