manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 64

56

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

Chlorinator 

Salt Level:3200ppm

 

Status: 

[OK-NO ERRORS] 

Water Temperature 

 

 

75° F 

Diagnostics Menu: Chlorinator

Displays the current IntelliChlor

®

 Salt Chlorine Generator system status. For more information, refer 

to the IntelliChlor Salt Chlorine Generator User’s Guide (P/N 520589).

MENU

s

DIAGNOSTICS

s

CHLORINATOR

Menu: 

Press this button to return to the Settings menu options. Press the 

button again to return to the main menu options or press again to return to 
the main screen.

SALT LEVEL: 

Displays the current salt level. Values from 0 to 12750 ppm in 

50 ppm increments.
IntelliChlor Status messages: 

SUPER CHLORINATE: 

IntelliChlor is in “Super Chlorination mode (see page 

35 for details)

COM LINK ERROR: 

Check cable from IntelliChlor to EasyTouch PL4/PSL4 

Control System mian circuit board.

Check FLOW/PCB:

 Check IntelliChlor electrolytic cell controller. Refer to 

IntelliChlor User’s Guide troubleshooting information.

LOW SALT: 

 Add salt to pool water. The water salt level is between 2500 

ppm and 2900 ppm. The IntelliChlor will continue to produce chlorine at a 
reduced level.

VERY LOW SALT: 

Not enough salt in pool. The water salt level has fallen 

below 2500 parts per million (ppm). IntelliChlor will not produce chlorine until 
additional salt is added manually. 

HIGH CURRENT: 

Check IntelliChlor electrolytic cell controller. Refer to 

IntelliChlor User’s Guide troubleshooting information..

CLEAN CELL!!:

 Cell has calcium build up and requires cleaning. Refer to 

IntelliChlor User’s Guide for cleaning instructions.

LOW VOLTAGE: 

Check IntelliChlor electrolytic cell controller. Refer to 

IntelliChlor User’s Guide troubleshooting information.

OK - NO ERRORS: 

IntelliChlor is in normal operating mode.  

Diagnostics Menu: Water Temp

Displays the current water temperature for the pool and spa.

MENU

s

DIAGNOSTICS

s

WATER TEMP

Press the 

Menu

 button to return to the Settings menu options. Press the 

button again to return to the main menu options or press again to return to 
the main screen.

 
Diagnostics Menu: Solar Temp

Displays the current solar temperature.

MENU

s

DIAGNOSTICS

s

SOLAR TEMP

Press the 

Menu

 button to return to the Settings menu options. Press the 

button again to return to the main menu options or press again to return to 
the main screen.

Solar Temperature 

 

 

85° F 

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands