manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 70

62

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

Problem: 

 iS4 fails to operate. 

Symptom

Possible Cause

Solution

iS4 Remote fails to operate 
equipment.

iS4 Remote is disabled.

See page 54 to enable the iS4.

Defective Wiring

Verify iS4 Remote setup. Ensure the iS4 Remote in 
question has the expected circuit assignments, and is 
not assigned to unused circuits.

Incorrect configuration 
or button setup.

See page 49 to setup the iS4 Remote buttons.

Defective iS4 Remote 

Replace defective iS4 Remote

iS4 fails to operate only some 
of the switches, but others work 
fine.

Defective wiring on one 
or more iS4 leads

Verify wiring on main circuit board and iS4.

Incorrect configuration 
or circuit to switch

 

assignment.

Verify circuit board connection.

System Problem Diagnosis 

Use the following information to resolve control system problems. 

Problem: 

The control system works in Service Mode, but EasyTouch PL4/PSL4 Control System Indoor 

Control Panel fails to operate.

Symptom

Possible Cause

Solution

Indoor Control Panel has no 
power - (screen, blank, no 
LEDs, buttons not working).

Bad wiring run from 
Outdoor Control Panel/
main circuit board in the 
Power Center.

Verify cable and ensure no connections are broken. 
In some cases a wire is broken under the insulation. 
The two center wires of the four conductor cable are 
suspect (Green and Yellow)

Indoor Control Panel lights up, 
but fails to operate correctly. 
The unit will not turn equipment 
on/off, or may turn some items 
on, but not off and may not 
LEDs near buttons on control 
panel.

Defective Cable/wiring

Verify cable and ensure no connections are broken. 
In some cases a wire is broken under the insulation. 
The two center wires of the four conductor cable are 
suspect (Green and Yellow)

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands