Pentair EASYTOUCH PL4 User Manual Download Page 65

Page: 65 / 80

EASYTOUCH

PL4/PSL4 Control Systems User’s Guide

Diagnostics Menu: Reset System

Reinitialize the Outdoor Control Panel. Resetting the Outdoor Control Panel will not effect the system
configuration settings.

MENU

DIAGNOSTICS

RESET SYSTEM

Right button:

Press the Right button to reset system. The main screen will be

displayed and communication will be established with the optional EasyTouch PL4/
PSL4 Control System Indoor Control Panel if installed.

Diagnostics Menu: Flash Update

Use this feature to update the EasyTouch PL4/PSL4 Control System Outdoor Control Panel firmware. The
EasyTouch PL4/PSL4 Control System main circuit board must be connected to a personal computer (PC) in
order to update the firmware.

MENU

DIAGNOSTICS

FLASH UPDATE

Press the

Menu

button to exit the flash mode.

Diagnostics Menu: Air Temp

Displays the current outside air temperature.

MENU

DIAGNOSTICS

AIR TEMP

Press the

Menu

button to return to the Settings menu options. Press the button again

to return to the main menu options or press again to return to the main screen.

Diagnostics Menu: Cir Name: [Off/On]

This feature is useful if you have renamed many circuits and want to view the original factory default circuit
names.

MENU

DIAGNOSTICS

CIR NAMES (OFF)

To enable:

Right button:

Select

to view the factory default circuit names.

Press the

Menu

button to exit.

To disable:

Right button:

Select

Off

to disable the feature.

Press the

Menu

button to exit.



Air Temperature

72° F





Solar Temp

Air Temp

Disp codes

Cir Names [Off]











Air Temp

Disp codes

Cir Names [Off]

Reset System

Press MENU

to exit

Summary of Contents for EASYTOUCH PL4

















































































Search results

Summary of Contents for EASYTOUCH PL4

Reviews:

Brands by name

Popular brands

Pentair EASYTOUCH PL4, User Manual

Search results

Summary of Contents for EASYTOUCH PL4

Reviews:

Brands by name

Popular brands