Panduit ATLONA OmniStream 101 Manual Download

Page: 134 / 147

Using OmniStream

™

with Velocity

™

Device Manager

134

The Velocity/OmniStream Interface

OTHER > LLDP page

eth window group

The Link Layer Discovery Protocol (LLDP) page returns information about the switch that the encoder is connected

to. If both interfaces from a dual-channel encoder are connected to the switch, then two

eth

window groups will be

displayed.

NOTE:

LLDP must be enabled on the switch that the encoders are connected to, in order for

the switch information to be displayed.

Via

The discovery protocol being used.

RID

The router ID.

Age

Up-time of the interface.

Chassis ID

The MAC address of the interface.

Chassis Capability

Indicates the device function, such as bridge (switch), router, etc.

Port ID

The port ID.

TTL

The Time-To-Live value.

Summary of Contents for ATLONA OmniStream 101




















































































































































Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands

Panduit ATLONA OmniStream 101, Manual

Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands