Panduit ATLONA OmniStream 101 Manual Download Page 113

Page: 113 / 147

Using OmniStream

™

with Velocity

™

Device Manager

113

Decoders

Alias

Enter a name for the unit in this field. This is optional.

Model

The model number of the unit.

Encoders

Decoders

AT-OMNI-111

AT-OMNI-121

AT-OMNI-112

AT-OMNI-122

AT-OMNI-512

AT-OMNI-521

IP Address

Displays the IP address of the encoder.

MAC Address

Displays the MAC address of the encoder.

Firmware Version

The version of firmware that the OmniStream device is running. Always make sure the latest version of firmware is

installed.

FIRMWARE UPDATE

Click this button to update the firmware.

DEVICE INFO page

The Velocity/OmniStream Interface

NOTE:

This section assumes that the

System mode

is set to

VCx

. If

VC-2 Video

VC-2 PC

Application

is used, some features on these pages will not be available.

Summary of Contents for ATLONA OmniStream 101




















































































































































Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands

Panduit ATLONA OmniStream 101, Manual

Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands