Panduit ATLONA OmniStream 101 Manual Download Page 119

Page: 119 / 147

Using OmniStream

™

with Velocity

™

Device Manager

119

The Velocity/OmniStream Interface

The

Serial

page provides serial port configuration when using control signals.

Supported Modes

Lists the supported protocols for the serial port.

Mode

Click this drop-down list to select the desired serial mode. Available values will be reflected in the

Supported

Modes

field.

Baud Rate

Click this drop-down list to select the desired baud rate:

19200

9600

Data Bit

Click this drop-down list to select the number of data bits:

, or

Parity

Click this drop-down list to select the parity bit:

None

Odd

Even

Mark

, or

Space

SERIAL page

Serial Port window groups

The following fields apply to both

Serial Port

window groups.

Summary of Contents for ATLONA OmniStream 101




















































































































































Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands

Panduit ATLONA OmniStream 101, Manual

Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands