Panduit ATLONA OmniStream 101 Manual Download Page 48

Page: 48 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Device Operation

Multiview and Dual-Streaming Tutorial

This section provides a tutorial on configuring a multiview setup. In addition, the concept of dual-streaming will be

introduced. Review the diagram and the table below for a summary of how this setup will function. All encoders and

the decoders should be connected to the same local network.

Physical Connections

AT-OMNI-111

AT-OMNI-121

PoE Network Switch

Laptop

Ethernet

HDMI IN

HDMI OUT

LAN

LINK

OMNI

STREAM

OMNI

STREAM

LINK

AT-OMNI-121

Display

Ethernet

OMNI

STREAM

LINK

AT-OMNI-121

Ethernet

OMNI

STREAM

LINK

AT-OMNI-111

HDMI IN

LINK

OMNI

STREAM

HD camera

720p

1080p

3.0

oom

F1.

4K + 1080p

1080p + 720p

Encoder #1

Encoder #2

Decoder #1

Display #1

Display #2

Display #3

Decoder #3

Decoder #2

OmniStream Device Description

Encoder #1

(AT-OMNI-111)

•

Dual-streaming configuration.

•

Transmits both 1080p and 720p streams.

Encoder #2

(AT-OMNI-111)

•

Dual-streaming configuration.

•

Transmits both 4K and 1080p streams.

Decoder #1

(AT-OMNI-121)

•

Multiview configuration (picture-in-picture).

• Subscribes to the 4K and 720p streams in multiview.

Decoder #2

(AT-OMNI-121)

•

Multiview configuration (side-by-side).

•

Subscribes to two 1080p streams in multiview.

Decoder #3

(AT-OMNI-121)

• Subscribes to a single 4K stream.

Summary of Contents for ATLONA OmniStream 101




















































































































































Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands

Panduit ATLONA OmniStream 101, Manual

Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands