Panduit ATLONA OmniStream 101 Manual Download Page 115

Page: 115 / 147

Using OmniStream

™

with Velocity

™

Device Manager

115

The Velocity/OmniStream Interface

Option

Description

None Checked

Resets the encoder with no factory-default settings.

Reset User

Resets the encoder to factory-default settings and resets custom user information.

Reset Network

Resets the encoder to factory-default settings and resets network information.

FACTORY RESET

Click this button to reset the encoder to factory-default settings. When performing a factory reset, the following

options can be selected, by clicking the check box. If no options are selected, then the encoder is reset with no

factory-default settings.

IDENTIFY

Click this button to physically identify a unit on the network. Clicking this button will cause all front-panel LED

indicators to flash for 10 seconds.

DEBUG

Click this button to instruct the unit to create a debug file. This file is used by Atlona Technical Support Engineers to

diagnose internal issues with the unit.

REBOOT DEVICE

Click this button to perform a soft reboot of the OmniStream device.

SAVE

Click this button to commit changes to the settings on this page.

Summary of Contents for ATLONA OmniStream 101




















































































































































Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands

Panduit ATLONA OmniStream 101, Manual

Search results

Summary of Contents for ATLONA OmniStream 101

Reviews:

Related manuals for ATLONA OmniStream 101

Brands by name

Popular brands