Panasonic YA-1W Series Operating Instructions Manual Download

Page: 47 / 72

External Control Signal Connection

OM1305066E26

7.9 Welding voltage/current monitor

In case of using welding voltage/current monitor function,
use the provided welding voltage/current monitor terminals.



Connecting to the monitor terminals

(1) Remove the terminal cover at the lower part of the con-

troller front panel.

(2) The monitor terminal is located on the left side of the

output terminal.

(3) In the same manner as output cable, lead the cable to

connect the external device and the monitor terminal
from the underside of the power.

(4) Re-install the output terminal cover back in place to

complete.



Layout and functions of the monitor terminals

Monitor terminals

Terminal name

Function

Welding current
monitor terminal

Connect a DC ammeter to between
these terminals to monitor welding
amperage.
(Output terminal from the shunt
resistor 600 A/ 60 mV.)

Welding voltage
monitor terminal

Connect a DC voltmeter to between
these terminals to monitor welding
voltage.

Note

Make sure to connect a DC ammeter and DC voltmeter individually.

Summary of Contents for YA-1W Series









































































Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands

Panasonic YA-1W Series, Operating Instructions Manual

Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands