Panasonic YA-1W Series Operating Instructions Manual Download

Page: 13 / 72

Specifications

OM1305066E26

2.7

Operation Box

The “AUTO” mode operation is functioned by
(1) Changing the Mode switch of the Teach Pendant to

“AUTO”

or
(2) Restarting after door stop input in “AUTO” mode, and

then the “AUTO mode” button of the Operation Box is
pressed.

The connection wires are connected to the Status I/O and
other connection terminals.



Location of PNL connector

Note

• Depending on the model numbers, the operation box is

factory connected at shipment.

• If not connected, the “PNL” terminal of the safety card is

factory short-circuited at shipment.

T / Y spec.

Optional

E / U spec.

Standard

Item

Specifications

Environmental protection class

IP40 or equivalent

“AUTO mode” switch

1 (Connect to the “PNL” connector of the sequencer card.)

Emergency stop switch

1 (Mechanical self-holding type. Connect to the “PNL” connector of the
safety card.)

Software

If the operation box is purchased as an optional unit, the initial setup by
our service engineer is needed.

Connecting cable

6 m

Safety card

Sequencer card

[Unit: mm]

Summary of Contents for YA-1W Series









































































Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands

Panasonic YA-1W Series, Operating Instructions Manual

Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands