Panasonic YA-1W Series Operating Instructions Manual Download | Manualshive

Page: 49 / 72

background image

Maintenance and Inspection

OM1305066E26

49

8.2 Daily check



Inspections before turning on the power

Note

(

*

)

: About filter at the air inlet fan

The air inlet fan at the side panels of the welding power
source unit is covered with a filter.
• Clean the filter periodically. And remove dust and/or

spatter attached to the filter. Using the controller with
clogged filter may degrade its cooling performance of the
fan, and performance of the robot will be deteriorated, as
a result, the “Temperature error” may occurs.

• In case of “Temperature error”(W1210, W1220), check

the filter and clean or replace it as necessary.
Adhesion of dust to the cooling fan of the built-in welding
power unit reduces cooling performance, which, as a
result, can cause the “Temperature error”. In that case,
clean the cooling fan.
(If the error recurs after cleaning the cooling fan, please
consult Panasonic representatives.)



How to replace filter

(1) Loosen the fixing screw of the filter fitting. Then

open the filter fitting and remove the filter.

(2) Insert a new filter into the filter fitting, and then

close the filter fitting. Then tighten the filter fitting
fixing screw.

Parts

Item

Service

Remarks

1

Ground cable
Cables

• Looseness
• Breaking or damage of wire

• Re-tightening.
• Replacement

2

Manipulator

Attachment of spatter or dust.

Removal of spatter or dust

Do not blow them off with
compressed air. Dust or spatter
may enter the clearance or
inside of the cover, resulting in
damage to the robot.

Looseness

Re-tightening

Consult our service section if
causes are not clear.

3

Safety fence

Damage

Repair

4

Welding torch
nozzle, tip

• Attachment of spatter.
• Wear at the tip hole

• Removal of spatter.
• Replacement

Be sure to replace with genuine
parts.

5

Controller

Attachment of spatter/dust.

Removal of spatter/dust.

Clogged filter.

Clean/replace filter

(

*

)

6

Working area

Tidiness

Filters at both (L/R) sides

Filter

Filter fitting fixing screw

Filter fitting

(4 pcs.)

«
...
47
48
49
50
51
...
»

Summary of Contents for YA-1W Series









































































Reviews:

No comments

Related manuals for YA-1W Series

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Campbell Pages: 2

Brand: dbx Pages: 2

Brand: Eagle Group Pages: 8

Brand: jcb Pages: 41

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Oakworks Medical Pages: 28

9NP-B7524 Series

Brand: Nautilus Pages: 2

Be strong NS 700X

Brand: Nautilus Pages: 34

Brand: Nautilus Pages: 21

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands