Panasonic YA-1W Series Operating Instructions Manual Download

Page: 44 / 72

External Control Signal Connection

OM1305066E26

7.6.3 Emergency stop 1

The following chart shows output terminal status to the
emergency stop operation when it is set to the safety PCB
connector OUTMB1.

Note

The chart is drawn as positive logical setting case.

7.6.4

Emergency stop 2

Status outputs of “Emergency stop output” and
“Emergency stop status output” vary with mode setting.

Note

The chart is drawn as positive logical setting case.

Power ON

(Setting - HOLD: OFF, EMG STOP: OFF)

Running output

HOLD status output

Servo ON

EMG STOP

(**)

Program execution

ON command

Open

Closed

Restoration

ON command is kept after completing PRG

If OFF command is not executed.

Opening file

START(TP)

HOLD EMG

EMG SERVO

PRG

PRG1

PRG2 reserved

(EXT reservation) (EXT Start)

(PRG1)

(PRG2)

End of PRG

Power OFF

ON command

OFF command

AUTO mode

(Setting - HOLD: LOCK, EMG STOP: OFF)

(Setting - HOLD: LOCK, EMG STOP: LOK)

output

EMG STOP

output

Restoration

Closed

Open

(EXT reservation)

STOP ON

(**)

: Output terminals status when it is set to the safety PCB connector OUTMD0.

Output terminal

STOP

released

START

reserved

start

Power ON

Mode

Servo Power

Enabling

switch

Door stop

Emergency stop status output

(*)

Emergency stop output

(*)

: Assigned to the common output terminal.

OFF

Servo ON

EMG STOP

Ignore

AUTO

TEACH

OFF

Closed

Open

Ignore

Open

Closed

(TP)

Servo ON

(TP)

Servo ON

(TP)

Summary of Contents for YA-1W Series









































































Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands

Panasonic YA-1W Series, Operating Instructions Manual

Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands