Panasonic YA-1W Series Operating Instructions Manual Download

Page: 46 / 72

External Control Signal Connection

OM1305066E26

7.8 External interface, External memory

7.8.1 SD Memory Card slot (Teach Pendant)

The teach pendant is equipped with a SD memory

card slot. Open the cover at the bottom of the teach
pendant to access the SD memory card slot.

Open the cove and attach the memory card to it to use.

7.8.2 USB port

The teach pendant is provided with two USB ports

on the left side of the SD memory card slot. You can
connect a USB-compatible keyboard or memory
when you use Windows CE.

<Usage note for USB port>

• The port supports USB 2.0 but does not support Hi-

Speed USB.

• Applicable devices for the port are keyboard and mem-

ory.

• Depending on the type of keyboard, some functions,

such as multimedia, are not available.

7.8.3 SD Memory Card slot (Main CPU card)

(1) Recovery SD memory card slot

It is a slot for TP version auto matching function
and Scheduled backup function.

“TP version auto matching function” is available with
the software version 9.00 or higher.

(2) User SD memory card slot

It is a slot for optional software.
No card is set in the slot at shipment.

SD memory card

Recommended product: (Product of Panasonic)
Part No.:

RP-SDL series

It supports SD memory (maximum capacity 2 GB)
and SDHC memory (maximum capacity 32 GB).

(SD cards of SDXC standard are not supported.)

Cover

USB port (2 ports)

SD memory

card slot

SD memory

card



Operation confirmed USB memory

Manufacturer

Product number

Capacity

BUFFALO

RUF3-K8GA

8 GB

GREEN HOUSE

GH-UFD4GN

4 GB

Recovery SD memory card slot

User SD memory card slot

Summary of Contents for YA-1W Series









































































Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands

Panasonic YA-1W Series, Operating Instructions Manual

Search results

Summary of Contents for YA-1W Series

Reviews:

Related manuals for YA-1W Series

Brands by name

Popular brands