Panasonic Minas-LIQI Series Technical Reference Download Page 19 | Manualshive

Page: 19 / 80

background image

№

SR-ZSV00039

－

15

－

Motor Business Unit, Appliances Company, Panasonic Corporation

4

－

2

－

2

Command Scaling (Electronic Gear)

This function multiplies a pulse command value input from the controller by the specified scaling factor to use as a posi-

tion command to the position control section. Using this function allows arbitrary setting of the motor revolution and dis-
tance per unit input command pulse and increase of a command pulse frequency when the required motor speed cannot be
obtained due to the limit to the controller pulse output capability.



Related parameters

Category

No.

Parameter

Setup range Unit

Function

0

08

Command pulse counts

per one motor

revolution

0



1048576

pulse

Specifies the command pulse count corresponding to one revolution
of the motor.
When this setting is 0, Pr0.09 "1st numerator of electronic gear" and
Pr0.10 "Denominator of electronic gear" are valid.
This setting is invalid in full-closed control.

0

09

1st numerator of

electronic gear

0



1073741824



Specifies the numerator for scaling for a command pulse input.
Valid when Pr0.08 "Command pulse counts per one motor revolution"
is 0 or in full-closed control.
When this parameter is set to 0, the encoder resolution is set to the
numerator for position control, and for full-closed control, the
command scaling ratio becomes 1:1.

0

10

Denominator of

electronic gear

1



1073741824



Specifies the denominator for scaling for a command pulse input.
Valid when Pr0.08 "Command pulse counts per one motor revolution"
is 0 or in full-closed control.

The relationships between Pr0.08, 0.09, and 0.10 in position control

Pr0.08

Pr0.09

Pr0.10

Command scaling

1



1048576



(No effect)



(No effect)

* The process shown in the above diagram is executed in

accordance with the set value of Pr0.08, regardless of set-
tings of Pr0.09 and Pr0.10.

0

1



1073741824

* When the set value of both Pr0.08 and Pr0.09 is 0, the

process shown in the above diagram is executed in accor-
dance with the set value of Pr0.10.

0

1



1073741824

1



1073741824

* When the set value of Pr0.08 is 0 and that of Pr0.09 is not 0,

the process shown in the above diagram is executed in ac-
cordance with the set values of Pr0.09 and Pr0.10.

Position
command

Encoder resolution *1

Command
pulse input

[Set value of P

r

0.08]

Position
command

[Set value of P

r

0.10]

[Set value of P

r

0.09]

Command
pulse input

Encoder resolution *1

Position
command

[Set value of P

r

0.10]

Command
pulse input

«
...
17
18
19
20
21
...
»

Summary of Contents for Minas-LIQI Series

















































































Reviews:

No comments

Related manuals for Minas-LIQI Series

Brand: LABTEC Pages: 12

Brand: Magnatone Pages: 5

Brand: Sansui Pages: 28

Brand: Opus Technologies Pages: 36

Brand: Trace Acoustic Pages: 13

Brand: NAD Pages: 78

Brand: Randall Pages: 2

Brand: Korg Pages: 36

Brand: aion Pages: 9

Brand: Ayre Pages: 24

Brand: NAD Pages: 37

Brand: DC Pages: 8

Brand: Texas Instruments Pages: 31

Tone Beast TB12

Brand: Warm Audio Pages: 2

Brand: Goldmund Pages: 14

Brand: Mark Levinson Pages: 20

Brand: DOD Pages: 4

Brand: Marshall Amplification Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands