manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 88

7-4 

7.2.1 Operation Status When a Communication Error Occurs 

"Communication error" is that the master station and any slave station cannot communicate with each 
other. This may occur because the slave station is not turned on, or the communication cable may not 
be wired correctly. 
Note) When the error occurs, "Remote I/O communication error" (Self-diagnostic error code E46) will be 
detected.The slave stations that cannot be communiated can be confirmed by the special data registers 
DT9131(DT90131) to DT9137(DT90137). 

 Reference: 

<9.4 Checking a Slave Station Which Has Produced an Error>

 

  

 

 

1. Operation status of normal slave stations 

When a communication error occurs, the following 4 types of operation can be seected for normal slave 
stations 

○

:Continue operation  ×: Halt operation 

System register 

Master 
unit 

Operation status when a 
communication error 
occurs 

Operation 
mode type 

No. 27

No. 28 

SW1/ 
SW7 

Note1)

 

Norm
al I/O

Remote I/O of  
slave stations 

Note3) 

Steps to take 

1) I/O operation: 
Halt [1] 

0 - OFF 

× 

×  
(COMM: Changes) 

Restart the 
master station. 

2) I/O operation: 
Halt [2] 

0 - ON 

× 

× 
(COMM: Not change)

Initialize 

3) Remote I/O 
operation: Halt 

1 - OFF 

○

 

×  
(COMM: Changes) 

Restart the 
master station. 

4) I/O operation: 
Continue 

1 - ON 

○

 

○

  

(excluding  
disconnected  
stations) 

If the cause of the 
error is removed, 
the slave station 
is automaticaaly 
reconfigured and 
starts operation.  

Note2) 

Note1) FP2 Multi-wire Link Unit: SW1, FP3 Master unit: SW7 
Note2) The slave stations which have not been able to communicate will start the operation once the 
communication error is eleminated (such as connecting cables and turning on the power supply again).  
Note3) COMM: COMM. LED(COM. LED) of slave stations  
 

If the mode selector switch "SW7" is off (so that the master unit will halt remote I/O control when a 
communication error occurs), all of the slave stations will stop outputting data when an error occurs. 
This operation is not affected by the mode selector switch "SW3" setting. 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands