Panasonic MEWNET-F Technical Manual Download Page 149

Page: 149 / 168

11-7

11.4 Specifications

11.4.1 General Specifications

Type

Consumption current

Weight

Power supply

voltage

Product No.

FP1 I/O Link Unit
[DC Power Supply Type]

0.1 A or less

Note1)

Approx.
230g

20.4 V DC to
26.4 V DC

AFP1732

FP1 I/O Link Unit
[AC Power Supply Type]

0.08 A or less
(When using 100 V)
0.06 A or less
(When using 200 V)

Note2)

Approx.
380g

85 V AC to
264 V AC

AFP1736

Note1) When connecting an expansion unit that has no power supply after an I/O link unit, the

consumption current is 0.2 A or less.

Note2) When connecting an expansion unit that has no power supply after an I/O link unit, the

consumption current is 0.12 A or less (when using 100 V)/0.08 A or less (when using 200 V).

11.4.2 Performance Specifications

Item

Specifications

No. of slots used by I/O link unit

1 slot

No. of I/O points occupied by I/O link unit

64 points (Input: 32 Output: 32 point)

Note1)

Allocation using remote I/O map

32X32Y

Note1) On the FP1, the input X70 to X8F and the output Y70 to Y8F are used (fixed).

Reference:

Summary of Contents for MEWNET-F









































































































































































Search results

Summary of Contents for MEWNET-F

Reviews:

Brands by name

Popular brands

Panasonic MEWNET-F, Technical Manual

Search results

Summary of Contents for MEWNET-F

Reviews:

Brands by name

Popular brands