manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 150

11-8 

11.5 Connection, Setting and Installation 

The FP1 I/O link unit is the interface to connect an FP1 and FP2/FP2SH/FP3/FP10SH. 
Connect with the FP1. 
The procedure to connect the I/O link unit is as follows. 
 

Be sure to connect or remove the transmission cable or expansion cable to the I/O link unit only when 
all power is OFF. 

 

11.5.1 Connecting to FP1 

With an FP1 expansion cable (flat cable), you can connect the expansion connector of the FP1 control 
unit and expansion connector of the FP1 I/O link unit. 

 

 

- 

Only one I/O link unit can be connected to one FP1 control unit. 

- 

An FP1 expansion unit can be connected after an I/O link unit.An I/O link unit can be connected after 

an FP1 expansion unit.The number of connectable expansion units is the same regardless of whether 
the I/O link unit is connected or not. 

- 

 

FP1 type 

No. of connectable expansion units 

16-point type Control unit 

Max. 1 unit 

24-point type Control unit 

Max. 2 units 

40-point type Control unit 

Max. 2 units 

* There is no restriction on the connected FP1 expansion unit. 

 

 Note: 

The connection as below is not possible. 

 

 

 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands