Panasonic MEWNET-F Technical Manual Download Page 22

Page: 22 / 168

2-4

Operation monitor LEDs

:Lights:

:Flashing
(T = 0.2 s),

:Flashing slowly (T = 1.0 s),

:Goes out:

Operation

LED

Descrip
tion

W mode

W2 mode

F mode

:Communicating
(Normal)

:Waiting for
communication

:Communicating
(Normal)

:Communication
buffer Overload

:Stop mode
Transmitting

COM.

Communicati
on status

:Communication error
(Transmission is not
available)

:Communication
error (Transmission
is not available)

:Communication
error

:Out of control/Self-
diagnostic
Error

:Out of control/
Self-diagnostic
Error

:Wait for starting error
(Note1)

:Wait for starting
error (Note1)

Setup error

:Various errors
(Note2)

ERR.

Hardware/
Software
error

:Normal operation

W mode

:In W mode

:Not in W mode

W2 mode

:Not in W2 mode

:In W2 mode

:Not in W2 mode

F mode

:No in F mode

:In F mode

:PC link operation
State

:PC link operation
state

:PC link Operation
impossible

PC-L

PC link flag
(Available in
W/W2 mode
only)

:PC link stop/
Non-PC link
operation State

:Non-PC link
operation State

:Not used

:500 kbps

Baud rate

:500 kbps fixed

:250 kbps

:500 kbps fixed

TERM.

Terminal
station

:Terminal station :Not terminal station

:Connected
:Not connected

1/17~

8/24

9/25~16/

Slave station
display
(Availalbe in
F mode only)

:Not used

* Slave station numbers
are switched by the
slave station number
selector.

Note1) It occurs when the version of CPU unit is Ver. 1.05 or older.
Note2) It occurs in case of transmission errors, when a station number is out of range, station numbers
are duplicated, or allocated link areas are duplicated.

Station number selector

Swithces the display range of the station number display.It is used in the F mode only.

Item

Setting

1-16

Indicates the monitor LEDs between the slave station
number 1 to 16.

17-32

Indicates the monitor LEDs between the slave station
number 17 to 32.

Summary of Contents for MEWNET-F









































































































































































Search results

Summary of Contents for MEWNET-F

Reviews:

Brands by name

Popular brands

Panasonic MEWNET-F, Technical Manual

Search results

Summary of Contents for MEWNET-F

Reviews:

Brands by name

Popular brands