manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 157

 

11-15 

11.7.1 When "MEWNET-F" Communication Error Occurs with I/O Link Unit 

If data cannot be transmitted between the I/O link unit and the master unit of FP2/FP2SH/FP3/FP10SH 
due to any cause such as the disconnection of transmission cable (a communication error occurs), the 
I/O link unit will operate as follows.  
 

1. I/O operation 

Mode selector switch

I/O operation 

SW3: ON 

Maintains the output on FP2/FP2SH/FP3/FP10SH. 

→

 Maintains the input 

relay on FP1. 

SW3: OFF 

Turns OFF the output on FP2/FP2SH/FP3/FP10SH. 

→

 Turns OFF the 

input relay on FP1. 

 

2. LED indication 

COM. LED: 

●

(OFF) 

 

3. I/O link error flag of FP1 (R9036) 

The occurrence of a communication error can be checked on the FP1 by monitoring the I/O link error 
flag R9036. 

Special relay name 

Status 

R9036 

0: Normal end 
1: Communication error occurs 

 
However, if a communication error occurs in another station, and when the mode selector switch "SW7" 
on the master unit is ON, it will not be activated.It will be activated only when the switch "SW7" is OFF. 

 

 

 

 Reference: 

For the information on the steps to take when a communication error occurs,  

<7.2.1  Operation Status When a Communication Error Occurs>

 

 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands