manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 69

 

5-7 

5.3.3 Procedure 2   Master Station (Master Unit) Setting 

Set the master unit. 
Note) The setting for FP2 Multi-wire Link Unit is different. 

 Reference: 

<FP2 Multi-wire Link Unit  ARCT1F284 2.2>

 

 

Selecting a transmission port (transmission line) 

Select a transmission port to be used and make the setting.Set the mode selector siwthces "SW3 & 
SW4" 

 

Set the mode selector switches "SW1 & SW2" to OFF as 
connection example. 

 

Configuring a terminal station 

When a slave unit is located at the end of a transmission line, the unit must be configured as a terminal 
station. 

 
Setting method 

Set the mode selector siwthces "SW3 & SW4". 

 

Set the mode selector switches "SW3 & SW4 to OFF as 
connection example. 
If the terminal stations are not properly configured, the 
ERROR LED on the CPU will be turned on when the power is 
turned on.(Self-diagnostic error code E51).Turn on the power 
again after making the correnct setting. 

 

Selecting an operation mode during a communication error 

Select whether to stop or continue the MEWNET-F control configured by this master unit when a 
communication error occurs.Set the mode selector switch "SW7". 
 

 

 

 Reference:  

The operation mode when a communication error occurs is related to the setting for the CPU of the 
master station. 
For the details of operation status, <7.2 Remote I/O Control When an Error Occurs" 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands