manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 39

 

2-21 

Output unit 
Terminal layout diagrams 

- 16-point type  Primary unit (AFP87424) 
         Expansion unit (AFP87428) 

 

- 8-point type  Primary unit (AFP87423) 
         Expansion unit (AFP87427) 

 

 
 

 

- In case of expansion unit, the terminals of 
the RS485 interface (pins 20 and 21 for the 8-
point unit, pins 36 and 37 for the 16-point unit) 
is N.C. (Not connected) terminals.These 
terminals are not connected internally. 

 Note: 

- Power supply input (24 V) terminal and all (+) terminals are internally connected. Power supply input (0 
V) terminal and all (-) terminals are internally connected.When using (+) or (-) terminal as a common 
terminal, use the one closest to the output terminal. 
- The screw terminals are all M3.5. 

 

 Note:Precautions when using an external power supply 

- Use an external power supply in the range of 20.4 V DC to 26.4 V DC.(It does not work with the power 
supply for operating.) 
- Up to 16 points can be used with the power supply of 0.5 A. (All the points can be simultaneously 
turend on.)However, in this case, use the (-) terminal that is close to the output terminal to be used. 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands