manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 23

 

2-5 

 

Station number selector 

Sets the station number of the master unit in the W/W2 mode.It is not used in the F mode. 

Operation  Setting 

W mode 

01 to 32: Available 
Other numbers: The station number setting error occurs. 
(Changing station numbers in operation is possible.) 

W2 mode 

01 to 64: Available 
Other numbers: The station number setting error occurs. 
(Changing station numbers in operation is possible.) 

Point the arrow to the number to be used. 

 
Mode selector switches 

 

Operation 

 

Setting 

SW 

W mode

W2 mode 

F mode 

OFF 

PC link mode 

The operation of the 
master unit stops when 
communication error 
occurs. 

Operation 
mode 

1 

ON 

Non-PC link mode 

The operation of the 
master unit continues 
when communication 
error occurs. 

2 

―

 

―

 

3 

―

 

―

 

4 

―

 

―

 

5 

―

 

―

 

Not used 

6 

―

 

―

 

7 

7: ON, 8: ON 

Terminal station 

Terminal 
station 
setting 

8 

7: OFF, 8: OFF

Not terminal station 

 

 

 

 

 

W mode 

W2 mode 

F mode 

1 OFF 

ON 

ON 

Operatio
n mode 

2 OFF 

OFF 

ON 

OFF 500 

kbps 

Baud 
rate 
Note2) 

3

ON 

500 kbps 
fixed 

250 kbps 

500 kbps fixed 

 

―

 

4 

Always set the switches to the OFF position. 

The swithces are all 
set to the OFF 
position at the 
factory. 

  

Note1) The setting of the mode selector switches is reflected in the operation 
monitor LEDs. 
Note2) In the W2 mode, a unit at 500 kbps and a unit at 250 kbps cannot be 
mixed in the same network. 
Note3) Be sure the power is off when changing the selector position (except the 
terminal station setting). 

 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands