Panasonic MEWNET-F Technical Manual Download Page 132

Page: 132 / 168

9-22

CPU

Master

Slave station

Contents

Actions

The communication
cable is not connected
correctly.

Check the
communication cable for
correct connection.

The slave station number
is duplicated.

Reset the duplicated
station numbers, and
assign I/O.
Then, restart the system.

COMM./
COM. LED
(OFF)

Terminal stations are not
assigned correctly.
(Self-diagnostic code
E51)

Both ends of
communication path
should be terminal
stations.

The communication
cable is not connected
correctly.

Check the
communication cable for
correct connection.
Check the ports of the
master unit.

COMM./
COM. LED
(ON)

The slave station is not
registered.

COMM./
COM. LED
(ON)

ERROR
LED
(ON)

ALARM LED
(Flashing)

The slave station number
is out of range (1 through
32).

Assign a slave station
number within the
applicable range.

LED status during the operation

CPU

Master

Slave station

Contents

Actions

RUN
(ON)

COMM./
COM. LED
(Flashing)

Normal

Error in a unit installed
on a slave station
system.

Exchange the bad unit
with a good one.The
procedures to restart the
system vary depending
on the operation mode.
Note1)

ERROR
LED
(ON)

COMM./
COM. LED
(Flashing)

Terminal stations are
not assigned correctly.
(Self-diagnostic code
E51)

Both ends of
communication path
should be terminal
stations.

COMM./
COM. LED
(Flashing)

COMM./
COM. LED
(OFF)

This slave station
cannot communicate
with the master
station.
(communication error)

Check the
communication cable for
correct connections.The
procedures to restart the
system vary depending
on the operation
mode.Note1)

COMM./
COM. LED
(Flashing
slowly)

Other slave stations
have a communication
error. (A slave station
whose COMM./COM.
LED is flashing is
normal.)

Check the
communication cable for
correct connections,
then restart the system.
Note1)

ERROR
LED
(ON)

COMM./
COM. LED
(Flashing
slowly)

COMM./
COM. LED
(OFF)

Other slave stations
have a communication
error. (A slave station
whose COMM./COM.
LED is flashing is
normal.)

Check the
communication cable for
correct connections,
then restart the system.
Note1)

Note1)

Reference:

<7.2 Remote I/O Control When an Error Occurs>

Summary of Contents for MEWNET-F









































































































































































Search results

Summary of Contents for MEWNET-F

Reviews:

Brands by name

Popular brands

Panasonic MEWNET-F, Technical Manual

Search results

Summary of Contents for MEWNET-F

Reviews:

Brands by name

Popular brands