manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 151

 

11-9 

11.5.2 Wiring to FP2/FP2SH/FP3/FP10SH 

Connect the RS485 interfaces on the I/O link unit and on the other station of the 
FP2/FP2SH/FP3/FP10SH remote I/O system [MEWNT-F] with a 2-conductor cable (VCTF0.75 mm

2

 x 

2C (JIS). 
Connects to the FP2/FP2SH/FP3/FP10SH system via [MEWNET-F].  
 
When connecting the transmission cable, be sure to connect postive (+) to positive, and negative (-) to 
negative of RS485 interfaces. 

 

* Connect one end of the shielded line of the transmission cable to the F.G. terminal, and ground it. 
 

- 

Set the appropriate I/O link units  in the transmission line of [MEWNET-F] as the terminal stations with 

the mode selector switches SW1 & SW2.  

 

 

 Reference:  

For information on the transmission cable specifications, <3.4 Transmission Cable Specifications> 
For information on the connection of transmission cables and the setting of terminal station, <Chapter 5 
Connection for the Remote I/O System> 
 

11.5.3 Wiring of Power Supply 

Supply power to the control unit, expansion unit, I/O link unit from the same power source so that power 
ON and OFF for all units can be performed at teh same time. 

 

 

 Note: 

Do not supply power to the DC power supply type unit from the terminal that supplies power for the input 
of the FP1 control unit or expansion unit. 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands