manualshive.com logo in svg

Panasonic MEWNET-F, Technical Manual

Share
Download
Panasonic MEWNET-F Technical Manual Download Page 2

Safety Precautions 

Observe the following notices to ensure personal safety or to prevent accidents. 
To ensure that you use this product correctly, read this User’s Manual thoroughly before use. 
Make sure that you fully understand the product and information on safe. 
This manual uses two safety flags to indicate different levels of danger. 
 

WARNING   

If critical situations that could lead to user’s death or serious injury is assumed by 
mishandling of the product.

 

-

Always take precautions to ensure the overall safety of your system, so that the whole system 

remains safe in the event of failure of this product or other external factor. 

-Do not use this product in areas with inflammable gas. It could lead to an explosion. 
-Exposing this product to excessive heat or open flames could cause damage to the lithium battery 

or other electronic parts. 

 
 

CAUTION   

If critical situations that could lead to user’s injury or only property damage is assumed 
by mishandling of the product.

 

-To prevent excessive exothermic heat or smoke generation, use this product at the values less than 

the maximum of the characteristics and performance that are assured in these specifications. 
-Do not dismantle or remodel the product. It could cause excessive exothermic heat or smoke 

generation. 

-Do not touch the terminal while turning on electricity. It could lead to an electric shock. 
-Use the external devices to function the emergency stop and interlock circuit. 
-Connect the wires or connectors securely. 

The loose connection could cause excessive exothermic heat or smoke generation. 

-Do not allow foreign matters such as liquid, flammable materials, metals to go into the inside of the 

product. It could cause excessive exothermic heat or smoke generation. 

-Do not undertake construction (such as connection and disconnection) while the power supply is on. 

It could lead to an electric shock. 

 
 
 
 

Copyright / Trademarks     

-This manual and its contents are copylighted. 
-You may not copy this manual,in whole or part,without written consent of Matsushita Electric   

Works,Ltd. 

-Windows and Windows NT are registered trademarks of Microsoft Corporation in the 
  United States and/or other countries. 
-All other company names and product names are trademarks or registered 
  trademarks of their respective owners. 
-Matsushita Electric Works,Ltd. pursues a policy of continuous improvement of the   
  Design and performan e of its products, therefore,we reserve the right to change the manual/ 

c

product without notice.

 

Summary of Contents for MEWNET-F









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands