Panasonic FA-DS72 Service Manual & Parts Manual Download Page 297

Page: 297 / 402

2-3

Mechanism

2.3 Bin drive

Up and down movement of each bin in the sorter is achieved by the rotation of the

bin motor (M1) located on the lower frame of the sorter. If any overdrive occurs,the

upper and lower limit switches(PI4 and PI5) (micro-switch) detect the abnormality

and protect the machine against damage.

(1) Rolls are fitted to both sides of each bin. The rolls are engaged in the groove of

the reed cam,which firmly secures each bin.

(2) The rotating motion of the bin motor is transmitted to the reed cam (front/rear)

through the bin drive belt. Rolls (for each bin) engaged in the groove in the

reed cam move up and down along the inclination provided in the reed cam,

thereby causing each bin up and down.

(3) The position of the cam is detected by the reed cam home position sensor

(PI2). This is achieved by turning the reed cam home position sensor (PI2) ON

each time the actuator on the reed cam (rear) completes a rotation.

FA-S620

LED ON signal

Upper limit detecting signal

Bin shift motor clock signal
Lower limit detecting signal

Bin shift motor drive signal

Reed cam rotation detecting
signal

Sorter controller circuit PCB

PI5

PI1

PI4

PI2

PS2

PI6

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands