Panasonic FA-DS72 Service Manual & Parts Manual Download Page 45

Page: 45 / 402

Preventive

Maintenance

4-5

Cloth with
water / IPA

Cloth with
water

Brush /
Vacuum
cleaner /
Cloth with
water

Cloth with
water

- Clean by cloth with water.

- Remove toner dust on separation

finger.

- Don’t damage separation finger

edge.

Cleaning position

Tool/solvent

Work/precaution

1 Sheet bypass paper

transfer roller

2 Sheet bypass paper

feed roller

3 Timing roller

4 Middle roller

5 Paper feed roller

6 Paper transfer roller

7 Cleaning sheet

Brush / IPA

8 Corona wire

9 Corona grid / Corona

case

10 Lower developer frame

Dust cover

11 Transport belt

12 Transfer corona wire /

Corona case/
Transfer guide plate

13 Fuser guide plate

Cloth

14 Fuser thermister

Cloth

15 Fuser separation finger Cloth

(upper/lower)

16 Fuser heat roller /

Cloth

pressure roller

Developer unit

Fuser unit

Paper feed unit

(to be continued)

- Use IPA, if toner is stuck on the

rollers. (As little as possible.)

- Do not use cleaning cotton.

- Remove paper dust by brush

deleted.

- If not replaced at PM cycle, high

voltage leak may occur.

- Pay attention when replacing corona

wire (No sagging or kinking)

- Do not use cleaning cotton.

- Lift the developer unit (mag-roll

side) up 45, and rotate mag-roller
4~5 times counterclockwise.
Remove the toner dust on lower
developer frame by brush or
vacuum cleaner.

- Clean the lower developer frame

by cloth with water.

- Use IPA, if the roller is very dirty.

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands