Panasonic FA-DS72 Service Manual & Parts Manual Download Page 67

Page: 67 / 402

Preventive

Maintenance

4-27

(1)Remove the platen cover (or ADF/i-ADF

if installed).

(2)Remove the copier front cover (refer to

page 4-18 step 1).

(3)Disconnect the lattice connectors of any

options (System Console and LCC).

(4)Remove the rear cover (7 screws).

Replacement of the optics motor belt/full-speed unit drive belt/half speed unit

drive belt

(1)Remove the copier top left and right

covers (4 screws).

(2)Remove the original guide, platen glass

and top rear cover (5 screws).

(3)Remove the copier left and right covers

(4 screws).

Remove the control panel ass’y.

(1) Remove the 4 screws.

(2) Disconnect the 2 connectors.

(3) Remove the ground wire (1 screw).

(1)Swing the toner hopper ass'y 180

degrees to the right.

(2)Remove the right side control panel ass'y

bracket (1 screw).

(3)Remove the inner front cover (3 screws).

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands