Panasonic FA-DS72 Service Manual & Parts Manual Download Page 86

Page: 86 / 402

5-9

Troubleshooting

Code

Function

Condition

Message display

No.

For FA-S575
a) Motor clock sensor

Signal is detected.

b) Bin ass'y upper/lower limit switch Bin is beyond the upper

limit or beyond the lower limit.

c) Cable safety switch

Cable is not loose.

d) Bin ass'y position sensor 2

Bin ass'y position is not placed
correctly.

e) Bin ass'y position sensor 1

Bin ass'y position is top Bin
ass'y. (#1 bin)

f) Paper exit sensor

Paper is not detected.

g) Paper feed sensor

Paper is not detected.

For FA-S615
a) Bin lower limit switch

Bin is placed less than lower
limit.

b) Bin cam home position sensor

Cam in home position.

c) Tamper home position

Bar in home position.

sensor

d) Transfer motor clock sensor

Clock signal is detected.

For FA-S575
a) Sorter detection switch

Sorter is pulled out.

For FA-S615
a) Bin paper detecting sensor

Paper is not detected.

b) Paper detection sensor for JAM

Paper is not detected.

c) Stapler detection sensor

Stapler is not installed.

For FA-S680
a) Sorter interlock switch

Sorter is installed.

b) Paper transport cover open/close Cover opened.

For FA-S680
a) Bin home position switch

Bin in home position

b) Bin cam switch

Bin cam in home postion

c) Tamper home position

Tamper in home position

sensor

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands