Panasonic FA-DS72 Service Manual & Parts Manual Download Page 82

Page: 82 / 402

5-5

Troubleshooting

Code

Function

Condition

Message display

No.

a) Sheet bypass paper detecting

Paper is not detected.

sensor

b) Sheet bypass paper size

Ledger/A3

detection sensor

Legal/B4-FLS
Letter/A4
Letter R/A4R
Invoice/A5

c) Platen open/close sensor

Platen is open.

d) Platen angle sensor

Platen is open more than
30 degrees.

e) Copier paper feed cover

Cover closed.

a) Developer cooling fan motor

Motor is locked.

b) +10V line error signal

+10V line is defective.

c) Discharge lamp error signal 1

Lamp is not lit.

d) Discharge lamp error signal 2

Lamp is not lit.

e) Dust collecting fan motor

Motor is locked.

f) Suction fan motor

Motor is locked.

g) High voltage leak detection

High voltage leak is not

(Separation corona)

detected. (Normal)

h) High voltage leak detection

High voltage leak is not

(Charge corona)

detected. (Normal)

a) Toner level detection

Toner is empty

b) Toner bottle position sensor

When the toner bottle is not
in the proper position.

c) Copier paper exit sensor

Paper is not detected.

d) Total counter

Total counter is not connected.

e) Key counter

Key counter is not installed.

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands