Panasonic FA-DS72 Service Manual & Parts Manual Download Page 61

Page: 61 / 402

Preventive

Maintenance

4-21

Replacement of the fuser lamp/heat roller/heat roller bearing/insulating bushing/

heat roller gear

• Conduct procedure 1and 2.

(1)Remove the screws (x 4)

(2)Remove the heat insulating cover.

Note: Either loosen pressure screws (x 2)

or install fuser shipping screws (x 2).

(1) (2) Remove the screws and take off the

thermistor and thermostat blocks.

(Lift the thermostat and slide to the front.)

(3)Remove the screws (x 2).

(4)Remove the roller pressure plates.

(5)Remove the heat roller.

• Remove the heat roller gear, bearing and

insulating bushing.

• Replace the heat roller.

Note: After reassembling and tightening the

screws of the pressure springs, check

the pressure roller for fit.

(1)Remove the springs.

1a 1b

(2)Turn the fuser lamp covers.

2a 2b

(3)Remove the fuser lamps (x2).

Note: The long one is the main fuser lamp.

(850W) Reassemble the lamp with the

rating indication in the rear.

850 W

550 W

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands