Panasonic FA-DS72 Service Manual & Parts Manual Download Page 143

Page: 143 / 402

6-6

Location

Shipping material/Procedure

Check

Hopper

Toner
bottle

Paper guides
(front/rear)

Toner bottle insertion

(1) Open the front cover.

(2) Take a fresh bottle of toner and

shake it 10 to 15 times.

(3) Swing the toner bottle hopper open

90 degrees.

(4) Remove the toner bottle cap.

(5) Insert the toner bottle into the

hopper unit and turn it clockwise.

Note: Make sure the arrows on the

bottle and the hopper are

aligned.

(6) Close the front cover.

Paper size setting

(1) Pull the paper drawer out until it

stops.

(2) Position the paper guides (front/

rear) to the paper size required. If

the size will remain fixed, install the

screws to lock down the paper

guides.

(3) Position the paper guide (left) to

the paper size required and install

the paper guide screw.

(4) Push in the paper tray.

(5) Select F5-15.

(6) Select the desired paper size.

(7) Press the “User Preset” and

"Clear/Stop" key simultaneously to

escape from the F mode.

(8) Take out and reinsert the indicator

so the selected paper size is

shown.

Paper guide (left)

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands