Panasonic FA-DS72 Service Manual & Parts Manual Download Page 347

Page: 347 / 402

Unpacking/

Installation

6-7

Location

Procedure

Check

Install the rail mounting bracket to

underside of the sorter (front and rear

side).

(4 screws, M4 X 8)

Pull out the rail assembly fully, and

install the sorter.

Note: Holding the set the sorter with

both hands as shown as the

figure. If hold the other parts,

sorter will be damaged.

Rail mounting bracket (rear)

Rail mounting bracket (front)

Summary of Contents for FA-DS72



















































































































































































































































































































































































































Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands

Panasonic FA-DS72, Service Manual & Parts Manual

Search results

Summary of Contents for FA-DS72

Reviews:

Related manuals for FA-DS72

Brands by name

Popular brands