104
DP-8032/8025
2008
Ver.1.2
3. Input the password, and select the
“OK”
button to enter the Service Mode (default password is
00000000
).
4. Perform the Service Mode F1-06 (Print Test Pattern 4).
5. Check the gap of the print pattern from the paper edge. (Refer to the “3.8.2. <Figure>”)
6. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm.
7. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.
8. Press the
“STOP”
key first, then press the
“FUNCTION”
, and
“C (CLEAR)”
keys simultaneously to
exit the Service Mode.
3.8.4.
100% Read Adjustment
1. Place the Original Document on the Platen Scanner.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the
“FUNCTION”
,
“ORIGINAL SIZE (LEDGER/A3)”
, and the
“3”
keys simultaneously.
4. Input the password, and select the
“OK”
button to enter the Service Mode (default password is
00000000
).
5. Perform the Service Mode F2 (Single Copy Test).
6. Check the Image size of the Copy and the Original as Portrait.
7. Perform the Service Mode F6-00 (Adj 100% Side-Side Read), to adjust the Side to Side to be the
same.
8. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value.
9. Perform the Service Mode F6-01 (Adj 100% Lead-Tail Read), to adjust the Top to End to be the same.
10. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value.
11. Press the
“STOP”
key first, then press the
“FUNCTION”
, and
“C (CLEAR)”
keys simultaneously to
exit the Service Mode.
Note:
This is the size adjustment and do not worry about the positioning.
3.8.5.
Original Registration & CCD Read Adjustments
1. Place the Original Document on the Platen Scanner.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the
“FUNCTION”
,
“ORIGINAL SIZE (LEDGER/A3)”
, and the
“3”
keys simultaneously.
4. Input the password, and select the
“OK”
button to enter the Service Mode (default password is
00000000
).
5. Perform the Service Mode F2 (Single Copy Test).
6. Check the Image size of the Copy and the Original as Portrait.
7. Perform the Service Mode F6-03 (Original Registration), to adjust the Original Registration.
8. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value.
9. Perform the Service Mode F6-53 (P Mode Image Density), to adjust the CCD Read for the side
position.
10. If the gap is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value.
11. Press the
“STOP”
key first, then press the
“FUNCTION”
, and
“C (CLEAR)”
keys simultaneously to
exit the Service Mode.
3.8.6.
ADF 100% Image 1-Sided Adjustment
1. Place the Original Document on the ADF.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the
“FUNCTION”
,
“ORIGINAL SIZE (LEDGER/A3)”
, and the
“3”
keys simultaneously.
4. Input the password, and select the
“OK”
button to enter the Service Mode (default password is
00000000
).
Summary of Contents for DP-8032
