Panasonic AJ-CX4000G, Operating Instructions Manual

Page: 205 / 221

– 205 –
Chapter 10 Maintenance — Warning system
Alert
Screen display
Description Behavior and cause
Camera image screen
[SIMUL REC WARNING <SLOT 2>]/
[SIMUL REC WARNING <SLOT 3>]
An error has occurred in one of the memory cards during
simultaneous recording.
A message is displayed for approximately five seconds.
f Recording to the other memory card will continue.
[SIMUL REC WARNING <SLOT 2>]/
[SIMUL REC WARNING <SLOT 3>]
Recording has been attempted while the number of clips
has exceeded the limit on one of the memory cards during
simultaneous recording.
A message is displayed for approximately five seconds.
f Recording to the other memory card will continue.
f [SIMUL REC WARNING <SLOT 2>] [<OVER MAX
NUM. OF CLIPS>]/[SIMUL REC WARNING <SLOT 3>]
[<OVER MAX NUM. OF CLIPS>] is displayed in the
message display area of the STATUS screen for the
mode check.
f Replace the memory card or delete unnecessary clips.
[FAN STOPPED] The fan has stopped. A message is displayed.
f The current operation will continue.
f Stop the use immediately when the fan has stopped and
alert is displayed, and consult the dealer.
f If the fan has stopped, temperature of the camera will
rise. Therefore, do not use the camera for a long period
of time. Use the tripod, etc., and do not touch the camera
directly.
[Non-supported card. <SLOT 1>]
[Insert expressP2 card.]
Card other than expressP2 card is inserted in the card slot
1.
A message is displayed for approximately five seconds.
f Insert an expressP2 card.
[ENCRYPTED CARD <SLOT 1>]/
[ENCRYPTED CARD <SLOT 2>]/
[ENCRYPTED CARD <SLOT 3>]
P2 card formatted with encryption with CPS (Content
Protection System) password is inserted.
A message is displayed for approximately five seconds.
f
The camera does not support the CPS function of the
P2 card. Insert a P2 card that is not formatted with
encryption with CPS password.
f Formatting P2 card, which was formatted with encryption
with CPS password, in the camera will enable P2 card to
be used as unencrypted card.
[REINSERT OR CHECK CARD
<SLOT 1>]/[REINSERT OR CHECK
CARD <SLOT 2>]/[REINSERT OR
CHECK CARD <SLOT 3>]
The memory card cannot be recognized properly because
a recording medium which is not supported has been
inserted or there is dirt on the terminal of the memory card.
A message is displayed for approximately five seconds.
f Check the memory card that is inserted.
f Insert the memory card again if displayed when inserting
a memory card.
[FORMAT ERROR CARD <SLOT 1>]/
[FORMAT ERROR CARD <SLOT 2>]/
[FORMAT ERROR CARD <SLOT 3>]
A memory card with management information out of
specifications has been inserted.
A message is displayed for approximately five seconds.
f Insert a memory card that can record.
[NOT SDXC CARD <SLOT 2>]/[NOT
SDXC CARD <SLOT 3>]
A SDHC memory card that cannot record the MOV format
data or a 32 GB microP2 card is inserted when [FILE
FORMAT] is set to MOV format.
A message is displayed for approximately five seconds.
f Insert a SDXC memory card or 64 GB microP2 card.
[INCOMPATIBLE CARD <SLOT 2>]/
[INCOMPATIBLE CARD <SLOT 3>]
A memory card that may not be able to record due to slow
writing speed has been inserted.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Use a memory card with sufficient writing speed.
[DIR NG CARD <SLOT 1>]/[DIR NG
CARD <SLOT 2>]/[DIR NG CARD
<SLOT 3>]
A P2 card with inappropriate directory placement is
inserted when [FILE FORMAT] is set to P2 format.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Take a backup of the memory card immediately, and use
it again after formatting.
[RUN DOWN CARD <SLOT 1>]/
[RUN DOWN CARD <SLOT 2>]/[RUN
DOWN CARD <SLOT 3>]
A P2 card exceeding the specified number of overwrites is
inserted.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Replace the P2 card.
[SD CARD <SLOT 2>]/[SD CARD
<SLOT 3>]
SD card is inserted when [FILE FORMAT] is set to P2
format.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Recording to a P2 card is recommended.
[SLOT1 CANNOT REC]
[microP2/SD SELECTED]
A memory card is inserted in card slot 1 when the
[RECORDING] menu → [REC MEDIA] → [microP2/SD]
is set.
A message is displayed for approximately five seconds.
f Set to the [RECORDING] menu → [REC MEDIA] →
[expressP2] when recording on the memory card inserted
in card slot 1.
[SLOT2/3 CANNOT REC]
[expressP2 SELECTED]
A memory card is inserted in card slot 2 or card slot 3 when
the [RECORDING] menu → [REC MEDIA] → [expressP2]
is set.
A message is displayed for approximately five seconds.
f Set to the [RECORDING] menu → [REC MEDIA] →
[microP2/SD] when recording on the memory card
inserted in card slot 2 or card slot 3.
[BACKUP BATT EMPTY] Voltage lowering of the backup battery for internal clock
was detected when the power is set to < j > (ON).
A message is displayed for approximately five seconds.
f The current operation will continue.
f Set the date/time again after charging the built-in battery.