Panasonic AJ-CX4000G Operating Instructions Manual Download | Manualshive

Page: 127 / 221

background image

– 127 –

Chapter 5 Shooting — Flash band compensation (FBC) function

Flash band compensation (FBC) function

The camera is equipped with a function for compensating and reducing band-like interference (called “flash band”) that occurs due to the MOS pickup
device when shooting in environments where flash strobe light such as that from still cameras is present.

Change over time

Shot image

(FBC OFF)

Flash firing

Flash band

Setting the flash band compensation function

Assign the flash band compensation function to the USER buttons.
By pressing the USER buttons that are assigned with the flash band compensation function, the function turns on, and flash strobe from a still camera,
etc. can be detected and compensated.
For details, refer to “Assigning function to the USER buttons” (page 129).
When the flash band compensation function is enabled, [FBC] is displayed on the STATUS screen.

INTRVL

HD

FLUO.

14.6V

FBC

RELAY

HDR

CAC

@

@

NOTE

t

When the flash strobe lights, the following phenomena may occur. These are due to the flash band compensation function and are not malfunctions.
-  Moving subjects look as if they have stopped suddenly.
-  The resolution when the flash strobe light drops.
-  Horizontal lines appear in the video when the flash strobe lights.
-  Flash bands may appear only in images shot at the time the flash is fired.

Using the flash band compensation function

The flash band compensation function is activated when there are large changes in brightness at the bottom of the screen regardless of whether there
is flash strobe light. The flash band compensation function may be activated depending on the shooting environment such as where a bright window has
zoomed in and then out. So, we recommend use of this function in shooting environments where flash strobe lighting is anticipated.
Even if flash strobe lighting occurs, sufficient flash band compensation function effect may not be obtained in some shooting environments.

Flash band compensation function operation conditions

f

The flash band compensation function can be used under the conditions that electronic shutter and digital super gain functions are all not operating.

f

Even if the flash band compensation function is enabled, the flash band compensation function is temporarily disabled if the camera is changed to a
mode where the flash band compensation function cannot be used.
When using the function again, return to a mode that can use the flash band compensation function. Flash band compensation function will be
automatically enabled.
The flash band compensation function is disabled once the power is turned off.

«
...
125
126
127
128
129
...
»

Summary of Contents for AJ-CX4000G






























































































































































































































Reviews:

No comments

Related manuals for AJ-CX4000G

Brand: Canon Pages: 4

Brand: SVP Pages: 1

Brand: Sony Pages: 15

Brand: Sony Pages: 21

Brand: Sony Pages: 25

CCD-CR1 - Video Camera Recorder 8mm

Brand: Sony Pages: 15

Brand: Sony Pages: 33

Brand: Sony Pages: 39

CCD-TR614 - Video Camera Recorder 8mm

Brand: Sony Pages: 56

CCD-TR517WR - Video Camera Recorder 8mm

Brand: Sony Pages: 68

CCD-TR516 - Video Camera Recorder Hi8&trade

Brand: Sony Pages: 76

CCD-TR315/TR416

Brand: Sony Pages: 76

CCD-CR1 - Video Camera Recorder 8mm

Brand: Sony Pages: 76

CCD TRV37 - Hi8 Camcorder

Brand: Sony Pages: 88

CCD-SC55 (English and Spanishl)

Brand: Sony Pages: 105

CCD TRV108 - Hi8 Camcorder With 2.5" LCD

Brand: Sony Pages: 100

Brand: Sony Pages: 128

Brand: Sony Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands