Home
/
Oki
/
IP-5630
/
User Manual

Oki IP-5630, User Manual, Page: 211 / 265

Share

Page: 211 / 265

Oki IP-5630 User Manual Download Page 211

211

Troubleshooting

Although the printer is in the print mode, printing does not start with

PREHEATING

displayed on the operation panel.

Items to be checked

Corrective measures

Room temperature

Raise the room temperature. (Recommended temperature: 20 to 25ºC)

Effect of air flow

If the air from an air conditioner or a fan is blowing against the paper guide, change the
air flow direction, the orientation of the printer, or the location of the printer.

The transmitted data is not printed.

Items to be checked

Corrective measures

ONLINE

LED (flashing?)

Check the communication conditions to the host computer.

Media jams occur frequently.

Items to be checked

Corrective measures

Media type

Check whether the media type setting matches the type of media installed.

Media installation

Install the media properly.
See

Loading the media on the printer

on

.

Obstructions in the carriage path
preventing the carriage from moving well

Remove any obstructions.
See

How to clear media jams

on

.

Obstructions in the media path preventing
the media from advancing well

Remove any obstructions.
See

How to clear media jams

on

.

Suction fan power

If the suction fan power is not proper, reduce the power.
See

Prevent the media from sticking and wrinkling

on

Heater temperature setting

If the heater temperature is not optimally set, lower the heater temperature.
See

Adjust the heaters temperatures

on

Print quality is poor.

See

Solve print quality issues

on

page 184

.

Printout are blank sheets.

Items to be checked

Corrective measures

Print data

Check the current print data to confirm that you sent blank sheet data.

Cannot load the media

See

Procedure to load transparent media and media with a black reverse side

on

.

«
...
209
210
211
212
213
...
»

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments