Home
/
Oki
/
IP-5630
/
User Manual

Oki IP-5630, User Manual, Page: 163 / 265

Share

Page: 163 / 265

Oki IP-5630 User Manual Download Page 163

163

Advanced operations

7

>>MISC SETTINGS

2

MEDIA ADVANCE MODE

Press the

OK

button.

8

>>>MEDIA ADVANCE MODE

2

FORWARD ONLY

,

Press the

Up

and

Down

buttons to select an

advance mode.

9

>>>MEDIA ADVANCE MODE

2

BACK & FWD LOW

Press the

OK

button.

10

>>>MEDIA ADVANCE MODE

2

BACK & FWD LOW

Press the

CANCEL

button to exit the MEDIA

ADVANCE MODE menu.

11

>>MISC SETTINGS

2

MEDIA ADVANCE MODE

Press the

ONLINE

button.

PRINTER READY
01: PAPER / 1626mm

Prevent the media from lifting up

The vacuum pressure applied to the media in the printing zone helps to hold the media down on the platen to keep
the distance from media to print heads constant.
When a gap tends to form between the media and the platen, set the vacuum pressure to HIGH.

1

PRINTER READY
01: PAPER / 1626mm

Press the

MENU

button.

2

MENU

2

INFORMATION

Press the

Down

button to select

EDIT MEDIA

PRESETS

.

«
...
161
162
163
164
165
...
»

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments