Oki IP-5630 User Manual Download Page 68

Page: 68 / 265

Loading the media

Procedure to unwind the media from the TUR unit

Follow the procedure below to unwind the media wound on the TUR unit.

PRINTER READY
01: PAPER/1626mm

Press the

MENU

button.

INFORMATION

Press the

Down

button to select

UNWIND

MEDIA

UNWIND MEDIA

Press the

button.

>UNWIND MEDIA
OK?

Press the

button.

>UNWINDING MEDIA...

The TUR unit starts unwinding the media.

Press the

button again to stop the unwinding of the

media.

The unwinding also stops if you press the

CANCEL

button to exit the UNWIND MEDIA menu.

Set the take-up direction switch to off then to the
desired direction to unwind the media several
times.

UNWIND MEDIA

Unwind the media from the

TUR unit

Summary of Contents for IP-5630










































































































































































































































































Search results

Summary of Contents for IP-5630

Reviews:

Oki IP-5630, User Manual, Page: 68 / 265

Search results

Summary of Contents for IP-5630

Reviews: