Oki IP-5630 User Manual Download Page 87 | Manualshive

Page: 87 / 265

Oki IP-5630 User Manual Download Page 87

87

Adjustment

16

>>>CARRIAGE SPEED

2

SLOW

Press the

CANCEL

button.

The following describes the procedure with automatic adjustment.

17

>>DETAILED 1

2

CARRIAGE SPEED

,

Press the

Up

and

Down

buttons to select

AUTO BIDIR ADJUST

.

18

>>DETAILED 1

2

AUTO BIDIR ADJUST

Press the

OK

button.

19

>>DETAILED 1
PRINT?

Press the

OK

button to print the bidirectional

adjustment pattern.

20

>>DETAILED 1
EXECUTING...

The printer prints the bidirectional adjustment pattern and
check the result with its sensors.
After printing and reading of the pattern is complete, the
bidirectional adjustment value with the specified print
conditions is set. The procedure is complete.

The following describes the procedure with manual adjustment.

17

>>DETAILED 1

2

CARRIAGE SPEED

,

Press the

Up

and

Down

buttons to select

BIDIR MANUAL

.

18

>>DETAILED 1

2

BIDIR MANUAL

Press the

OK

button.

19

>>>BIDIR MANUAL

2

PRINT PATTERN

Press the

OK

button.

«
...
85
86
87
88
89
...
»

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments