Home
/
Oki
/
IP-5630
/
User Manual

Oki IP-5630, User Manual, Page: 108 / 265

Share

Page: 108 / 265

Oki IP-5630 User Manual Download Page 108

108

Maintenance

Wiper blades replacement

Replace the wiper blade in the following cases.

- When a printer message prompts you to do so.
- When you notice that the blade is not clean or damaged during a daily inspection.

Follow the procedure below to replace the wiper blade.
Wiper blade replacement is performed in two steps: first replace the sponge blade, and then replace the two rubber
blades.

1

PRINTER READY
01: PAPER / 1626mm

Press the

MAINTENANCE

button.

2

MAINTENANCE

2

START MAINTENANCE

Press the

Down

button to select

WIPER

MAINTENANCE

.

3

MAINTENANCE

2

WIPER MAINTENANCE

Press the

OK

button.

4

>WIPER MAINTENANCE

2

REPLACE BLADE

,

,

Press the

Up

and

Down

buttons to select

REPLACE BLADE

, and then press the

OK

button.

5

>>REPLACE BLADE
OK?

Press the

OK

button to start the operation.

To cancel the operation, press the

CANCEL

button.

6

CARRIAGE IS MOVING
PLEASE WAIT

Carriage stops moving.

«
...
106
107
108
109
110
...
»

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments