Oki IP-5630 User Manual Download Page 213

Page: 213 / 265

213

Troubleshooting

How to clear media jams

MEDIA JAM ERROR

LIFT THE LEVER

The message to the left appears.

X: Media jam type

Meaning

1: Media jam 1

A jam on the carriage is preventing the printer from operating correctly.

2: Media jam 2

A media not supported is used. The media cannot be detected correctly.

3: Media jam 3

An obstruction in the carriage path, such as media wrinkles, prevents the printer
from operating correctly.

Lift the pressure roller lever and open the
front cover.

When you lift the lever

OPEN COVERS AND
REMOVE MEDIA

When you open the cover

LIFT THE LEVER AND
REMOVE MEDIA

Clear the media jam, make sure that no obstruction is left in the carriage path and the media
feed path, and then close the front cover.

Note

In case of roll media, rewind some of the media.

To manually move the carriage...

If the carriage must be moved manually, slide the
carriage by softly pressing locations indicated with
the arrows.

Summary of Contents for IP-5630










































































































































































































































































Search results

Summary of Contents for IP-5630

Reviews:

Oki IP-5630, User Manual, Page: 213 / 265

Search results

Summary of Contents for IP-5630

Reviews: