NSD VARICAM VS-5F Series Specifications And Instruction Manual Download Page 120

Page: 120 / 130

110

APPENDIX

APPENDIX 1. PASSWORD FUNCTION

APPENDIX 1-4. Mode Selection Procedure after Setting the Password

Explains the operation procedure of mode selection after setting the password.

The password must be input when changing the mode from operation (RUN) to parameter (PRM) or switch setting
(SET).

①

Displays the mode selection screen.

Keeps pressing [MODE] key more than 1 second.
POSITION and MODE display areas are blinking, and

changes to mode selection screen.

②

Changes the mode.

Repeatedly presses [MODE] key, and selects the
parameter setting (PRM) or switch setting
(SET) mode.

③

Displays the password input screen.

Presses [SET] key.
“PAS” is blinking in the POSITION display area.

④

Inputs the password.

Inputs the password by pressing
[+] or [-] key of POSITION.

If [CLR] key is pressed in this timing,

returns the operation (RUN) mode.

⑤

Enter the password.

Presses [SET] key.

- Returns to the mode which is selected in procedure

②

when the password is correct.

- Returns to the operation (RUN) mode if the password is incorrect.

Operation (RUN) mode Switch setting (SET)mode Parametr setting (PRM) mode

Password input screen

LED ON/OFF state

: ON

: OFF

: BLINK

Summary of Contents for VARICAM VS-5F Series



































































































































Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Related manuals for VARICAM VS-5F Series

Brands by name

Popular brands

NSD VARICAM VS-5F Series, Specifications And Instruction Manual

Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Related manuals for VARICAM VS-5F Series

Brands by name

Popular brands