manualshive.com logo in svg

NSD VARICAM VS-5F Series, Specifications And Instruction Manual

Share
Download
NSD VARICAM VS-5F Series Specifications And Instruction Manual Download Page 67

        

 

 

57 

 

OPERATION 

7. HOW TO USE BASIC FUNCTION 

  

 

[ 3 ] Selects the Operation (RUN) Mode 

 

Selects the operation (RUN) mode, refer to the procedure [1]. 

 

[ 4 ] Operation (RUN) 

 
The switch output turns ON or OFF according to the setting value during the operation. 
Indicates the monitor contents during the operation. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Name 

Descriptions 

①

  MODE indicator 

RUN LED is ON: Indicates the operation (RUN) mode. 

②

  PROGRAM display  Displays selecting the program number. 

(VS-5F and VS-5F-1 are not available this function.) 

③

  SW / PRM display 

Displays the switch number which is selected by SW /PRM key. 

④

  RDY indicator 

If there is no error, this indicator will turn ON when selecting operation (RUN) mode. 

This indicator is same condition as “System ready output signal” of the output connector. 

⑤

  DOG display 

Monitors the switch number output state that is selected by SW / PRM key.   
 
ON  :             OFF  :        
 

⑥

  POSITION display 

Displays the current position value. 

⑦

  SW / PRM key 

Selects the switch number that is monitored on DOG display area. 

①

      

②

 

③

     

④

   

⑤

          

⑥

 

⑦

 

Summary of Contents for VARICAM VS-5F Series



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands