NSD VARICAM VS-5F Series Specifications And Instruction Manual Download Page 102

Page: 102 / 130

OPERATION

10. HOW TO USE APPLIED FUNCTIONS (OPERATION MODE)

10-2. Monitor Contents

(1) Monitoring the current position value

The current position value and ON / OFF state of the switch output can be check during the operation.

Name

Descriptions

①

POSITION display

Displays the current position value.

②

PROGRAM display Displays selecting the program number.

(VS-5F and VS-5F-1 are not available this function.)

③

SW / PRM key

Selects the switch number that is monitored on DOG display area.

④

SW / PRM display

Displays the switch number which is selected by SW /PRM key.

⑤

DOG display

Monitors the output state of the switch number which is selected by SW / PRM key.

ON : OFF :

⑥

MODE indicator

RUN LED is ON: Indicates the operation (RUN) mode.

⑦

RDY indicator

If there is no error, this indicator will turn ON when selecting the operation (RUN) mode.

This indicator is same condition as “System ready output signal” of the output connector.

⑥

②

④

⑦

⑤

①

③

Summary of Contents for VARICAM VS-5F Series



































































































































Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Related manuals for VARICAM VS-5F Series

Brands by name

Popular brands

NSD VARICAM VS-5F Series, Specifications And Instruction Manual

Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Related manuals for VARICAM VS-5F Series

Brands by name

Popular brands